Scooter-Scene :: View topic

Posted: Wed Feb 24, 2010 5:52 pm

hi has anyone bought one of thoughs p2 rz revolver exhausts on ebay there stainless steel and right hand side.just wondred what the perfofmance was like..........

Posted: Wed Feb 24, 2010 6:18 pm

I have a steel RZ right hand and it gives very good power, not sure if they made them in stainless though Confused

Posted: Wed Feb 24, 2010 6:38 pm

they are on ebay at the mo.take a look..is it the same as yours

Posted: Wed Feb 24, 2010 7:08 pm

looks the same, steel ones are £200ish new so I am a bit sceptical about these

Posted: Wed Feb 24, 2010 8:06 pm

seen one today.it looked pretty good all the welds were spot on.this seem to be selling for bout 100 quid.if you are lucky on ebay..just wondered if there was a differents betweem stainless steal.and steal exhausts

Posted: Wed Feb 24, 2010 8:09 pm

stainless hold the heat more and can lead to overheating probs, they also expand differently when hot. I was told by a good tuner to never have a stainless. On the plus side though it wil last

Posted: Wed Feb 24, 2010 8:14 pm

have they had lots of problem with the scorpion pipes..i had one and no prob.....but...i didnt have it that long before i swaped it

Posted: Thu Feb 25, 2010 1:51 pm

not heard of any probs.

if these RZ are genuine I changed from a left hand SIP to one took it out for a blast and holed a piston in about 10 miles, so beware will need serious rejetting

Posted: Thu Feb 25, 2010 2:43 pm

what do you recon.to use.im running a 124 on my p2 with a mikeck..on a standard carb..would you change anything eles other than the main jet.

Posted: Thu Feb 25, 2010 5:48 pm

I just rejetted and changed timing, I run pinasco 213/standard carb

Posted: Tue Mar 02, 2010 5:27 pm

they are the real deal they are sold in scooter center in cologne ("the only place you could buy a rz pipe iirc") i have just took delivery of one and its ok its made very well
as for problems running stainless pipes yay and nay my t5 172 ran with a stainless scorpian for a good while with no issues
i dont think they let go of the heat a bit and you lose a couple of hp but is that a great loss over a pipe thats non rusting

Posted: Fri Mar 26, 2010 10:21 am

iv had the rz on the scoot now for a mouth now.it was easy to to fit eg no hammers.perfect fitting good rear wheel clearences with no rubbing anywhere..it on a standard px125.and is much kwicker than a mates px166.the stainless looks as good as chrome..so if anyone may be intressted in one for your px125 or p2.i can probly get them for 150quid

Posted: Sat May 01, 2010 6:30 pm

There must be something very wrong with your mates 166!!!

Posted: Mon May 17, 2010 4:00 pm

its probly cause hes is bout 18stone..lol

Posted: Mon Aug 23, 2010 7:07 pm

I just binned my Simonini and brought a RZ revolver from ebay for my 03 P2...Payed £120.00 and that included delivery. Did a bit of research and realised the exhaust is not made by RZ but a copy. However when the exhaust arrived I have to say I was really surprised despite being a RZ copy the build quality was excellent, all welds looked good and stainless steel look of it seemed faultless. Was still dubious about putting on the scoot but got it on without any probs, upjetted to a 120 and fired her up. Sound was awesome, nice deep but cracling type of sound, far crisper than the Simonini.
Took her out for a good cane and loved the torqueness around town then opened her right up on a motorway. She pulled and went through the gears beautifully. Took the scoot up to just over 70 and still had a fair bit more in her, will take it higher when the exhaust has been on for a couple more weeks. Have to say for the money the exhaust is brilliant, looks and sounds great on the scoot and am really pleased bearing in mind this is the same price as a Simonini but wont rust.
See ya at the IOW Very Happy